Jax Auto Repair

Servicing Brea and the surrounding area since 1985

Jax Auto Repair - Servicing Brea and the surrounding area since 1985

Coolant Service at Jax Auto Repair

Brea motorists’ cars have to operate in a wide range of California temperatures which requires our engine coolant to be able to perform ‘no matter what’. Think for a moment about the environment where the coolant does its thing. Very hot, high pressure, corrosive…

And all the while, it has to protect the components of the cooling system from corrosion. These components are made from steel and aluminum, plastics and rubber. The coolant has to be formulated to protect against corrosion for all of these different materials. That’s why car makers recommend different types of anti-freeze for our Brea, California vehicles.

There are several different ‘families’ of anti-freeze available to us here in Brea, California. Your owners’ manual will tell you what kind you should use. Of course, the automotive professionals at  Jax Auto Repair will know the right kind for your car.

It’s vital to stay on top of this because coolant system failure is the most common mechanical problem people have here in Brea, California. Regular service at Jax Auto Repair needs to be done to avoid failures and also to keep your warranty in place.

While the specifics of the service required may vary from vehicle to vehicle, your friendly Jax Auto Repair technician will know what to do. You’ll be advised to replace the coolant at specified intervals.

Some manufacturers recommend periodic coolant system flushes. A flush adds a cleaning step to the fluid replacement process. Again, check to see what your Brea service specialist recommends.

Someday, you may have to deal with an overheating problem, so you need to know what to do if your coolant temperature warning light comes on or your temperature gauge is in the hot zone.

Now, overheating can be very expensive. Brea auto owners can literally melt down their engine and have to replace the whole thing. So don’t ignore warning signs.

First turn off the air conditioner. This will lower engine temperature right away. Next, crank up your heater to maximum heat and run the fan at high speed. You might need to roll down the windows, but this will take a lot of heat off the engine.

Pull over as soon as you can safely do so
, especially if you are stuck in slow-moving traffic, and shut the car off. It may take as much as 45 minutes for the engine to cool to the point that it’s safe to operate the car again.

If you need to add water or antifreeze, be sure to wait until the car cools down. Opening the radiator cap or even the overflow bottle when the coolant is hot and under pressure may result in serious burns.

After the engine has cooled for 45 minutes or so, look to see if the coolant is low in the overflow tank. If so, you can cover the overflow tank cap with a large cloth and open the lid. Then start the engine and pour in some water or antifreeze. Pouring it in when the car is running will circulate the new, cool fluid with the warmer fluid in the engine and avoid engine damage.

Of course, overheating is a serious problem and you need to get it fixed right away. Jax Auto Repair can make sure the coolant is right before you drive home.

Those spring and winter inspections really come in handy when they head off a cooling system problem. And don’t forget that severe service driving conditions, like towing or hot, dusty driving around Brea, California, mean that you’ll need to service your coolant more frequently.

At AutoNetTV, we suggest that you have Jax Auto Repair inspect your coolant system to find small problems before they become big, and to change belts and hoses before they fail. After all, we don’t want you to lose your cool out there in Brea, California.

Water Pump

Your cooling system is very important. It circulates coolant through the radiator and your engine to protect your car from overheating. There are five main components to the cooling system:

  • the radiator
  • the radiator cap
  • the hoses
  • the thermostat and
  • the water pump

The cooling system is important for Brea drivers. It circulates coolant through the radiator and your engine to protect your sedan from overheating. There are five main components to the cooling system:

the radiator
the radiator cap
the hoses
the thermostat and
the water pump

The water pump’s like the heart of your cooling system, circulating the fluid throughout your sedan. It’s a small pump that’s driven by the engine; usually by belt, but sometimes by a chain or gear.

The water pump only operates when the engine’s running. Water pump failure is pretty routine. We see it often at Jax Auto Repair. Some start failing at around 40,000 miles, but most fail by 100,000 miles. Consult your automobile manufacturer’s owners’ manual or friendly Jax Auto Repair service advisor to see what’s recommended.

Since a water pump either works or it doesn’t, you need to change it when it fails. Water pumps fail in one of two ways: the bearings fail or they begin to leak. It’s possible to have a leak from a cracked water pump, but it usually leaks at the gasket where it attaches to the engine.

So how can Brea motorists tell when the water pump is failing? If you can hear a low-pitched grinding sound coming from the water pump – it’s got a problem. If you can see coolant in that area, you’ve got a leak.

Some water pumps are driven off the timing belt. They might be under a plastic cover so you can’t see the water pump. Look for coolant on the driveway. If you see some, have your Jax Auto Repair service specialist check it out.

Most timing belts need to be changed at 60,000 miles – some longer. It’s a good idea to change your water pump at the same time if it’s one of those that’s driven off the timing belt. To start with, 90% of the work’s already done with the timing belt change. And, if you don’t, and develop a leak later, you’ll have to change the belt again along with the water pump because the belt will have been contaminated by the leaking coolant.

Brea drivers can replace a failed water pump with a brand spankin’ new one or with a rebuilt pump. Rebuilt will save you some money, but ask your friendly Jax Auto Repair technician what he thinks. Don’t feel too bad if your water pump gives out. They will all wear out eventually. Your Jax Auto Repair service professional can get you back on the road and on with your life.

Cool Running In Brea

Unless you live in Death Valley, you really don’t hear much any more about cars overheating. That’s because cooling systems in vehicles have been much improved. That doesn’t mean you can’t overheat your sedan engine, though. Without proper preventive maintenance, you could still find yourself on the side of the expressway in Brea waiting for your sedan engine to cool down.

When you service your cooling system at Jax Auto Repair, your technician will check the condition of the coolant. It can become corrosive over time, which can damage a radiator — leading to an overheated engine. Changing the coolant periodically is good car care. Your sedan owner’s manual can give you guidelines on how often to replace it.

If your engine overheated, your friendly tech will also check your coolant system for leaks. Check the sedan radiator for cracks and the radiator hoses for leaks. He’ll also check your water pump. They don’t need to be replaced on a regular schedule, but they do need an inspection regularly. They can and do wear out.

The water pump is a critical component of your sedan cooling system. It pumps the coolant to keep it circulating through the engine. The coolant is cooled in the radiator, then it travels through the engine, where it absorbs heat, then it returns to the radiator, where it releases the heat. And so on. But a water pump is something of a misnomer. The fluid pumped through your sedan cooling system is not just water. It also contains coolant, which is actually poisonous. You should never consider your radiator as an emergency water supply.

There are many types of coolant. It varies from vehicle to vehicle, and using the wrong kind could damage your engine. Your service advisor will know which kind your vehicle’s manufacturer recommends. The team of automotive professionals at Jax Auto Repair is always a good source for auto advice. We’ve been providing quality automotive services at our convenient location in Brea for 27 years.

Keeping your cooling system in good repair will help keep your engine running well, and keep you out of the La Habra repair shop. This means that a regular cooling system inspection should be on your schedule for routine preventive maintenance of your vehicle. Your owner’s manual will tell you how often you need to do this. It varies depending on what kind of car you drive, what type of driving you do and where you live in California.

At Jax Auto Repair, we help you keep your cool which will keep you in the driving lane.

Keeping Your Engine Cool In Brea, California

The cooling system keeps California auto owners’s engines from overheating while they are driving around Brea, Buena Park and Yorba Linda. Its job is to move heat away from the engine. Let’s talk about the various components of the system and how they make this happen.

The radiator is the part most Brea car owners associate with the cooling system. Coolant flows through the radiator which has fine cooling fins that draw the heat out of the coolant and dissipate it into the air. To make sure there’s enough airflow over the radiator, a fan pulls air over the cooling fins even when the sedan is idling.

In some sedans, the fan is powered by the serpentine belt. On others, an electric motor runs the fan. Electric fans turn on and off as needed. You may have heard the fan kick on shortly after you turn your sedan off. The sensor has determined that the engine needs a little help cooling down to a safe temperature.

Brea California Radiator A hose connects the radiator to the water pump. The water pump pushes the water into the sedan engine block. Now the engine block and cylinder heads have passages for the coolant to pass through without getting into the oil or the combustion chamber. In the automotive community, these passages are referred to as the “water jacket”.

While the coolant is passing through the water jacket, it absorbs heat from the sedan engine on its way to the radiator for cooling. Between the engine and the radiator is a gatekeeper called the thermostat. The thermostat’s job is to regulate the temperature of the engine just like your home thermostat regulates the temperature in your Brea house. It gets your engine up to the correct operating temperature and then keeps it from overheating.

When you first start the engine, it’s very cold and needs to warm up. So the thermostat blocks the flow of coolant to the radiator. As the engine warms up, the thermostat starts to let coolant flow through the system.

The final component the team at Jax Auto Repair wants to point out is the overflow reservoir. This bottle is designed to hold some of the coolant. It’ll have a mark that indicates whether or not you have enough coolant. This is where you should add coolant if you just need to top it off.

Caution: never open the reservoir or the radiator cap when the car’s hot. The cooling system is pressurized and opening them while it’s hot can cause hot coolant and steam to escape resulting in serious burns.

Cooling system failure is the most common mechanical failure in vehicles around Brea, California. At Jax Auto Repair, we can do a periodic inspection of the components for harmful leaks, loose connections and weakening hoses.

Jax Auto Repair
331 South Brea Boulevard
Brea, California 92821
(714) 529-2886

Your auto manufacturer has also specified a cooling system service interval. With a cooling system service at Jax Auto Repair in Brea, the old coolant is replaced with correct clean fluid that contains the additives required to prevent corrosion. The additives are depleted over time and you need fresh fluid for adequate protection. Your radiator pressure cap should be replaced at this service as well.

Smart Brea Drivers Protect Against Overheating

Engines get hot when they run. This heat can build up and damage vital engine parts, so engines need a cooling system to keep them running. Cooling system failure is the most common mechanical failure in vehicles. This is unfortunate, because these failures are usually easy for Brea auto owners to prevent.

The radiator is the best-known and most recognizable part of the cooling system. Hoses filled with coolant (also known as antifreeze) connect the radiator to the engine. The coolant draws heat from the engine, and then flows to the radiator. Air passing through cooling fins on the radiator cools the coolant. The coolant then cycles back into the engine to start the process over again.

The most critical component of the cooling system, however, is the coolant itself. A mixture of water and coolant/antifreeze helps keep it both from freezing and from boiling away. Either can result in serious engine damage.

Different engines require different types of coolant/antifreeze. The owner’s manual will list what kind a vehicle requires. Using the wrong type or mixing different types of may void the warranty on the cooling system and may damage it as well.

Insufficient coolant can lead to engine failure. Coolant levels need to be checked regularly and topped off as necessary. If coolant levels drop quickly or consistently, the cooling system should be inspected for leaks. Coolant/antifreeze contains additives that protect the radiator and other coolant components from rust, scale and corrosion. Over time, these additives are depleted, so it is necessary for Brea drivers to replace coolant at specified intervals. Changing coolant should be part of routine preventive maintenance for any vehicle.

This service is often ignored, though, since old coolant still cools the engine. Vehicle owners don’t realize there is a problem until the system fails. They are left with major repairs and possibly a damaged engine, which could have been prevented with a cooling system service at Jax Auto Repair in Brea.

If your sedan sends a warning message to check its coolant or if the temperature gauge is reading in the red or hot zone, then the cooling system needs an automotive analysis. This service is important and should not be put off since the potential for damage is high.

In an emergency situation, water or antifreeze can be added to your sedan so that it can be driven to a service center for proper car care. For this reason, owner’s manual contains instructions for how to top off insufficient coolant – allow 45 minutes for the engine to cool before attempting to add coolant or water. However, the fluid should be added to the coolant overflow bottle, not to the radiator itself. Removing the radiator pressure cap can result in severe burns.

Topping off in an emergency, however, does not fix the problem. The vehicle should immediately be taken to your Brea service center or Jax Auto Repair where they can inspect the cooling system, repair any leaks, and clean it if necessary. They can identify what caused the emergency situation in the first place and ensure it doesn’t happen again.

Regular maintenance of a vehicle’s cooling system is just good auto advice for Brea motorists. Cooling system service is relatively inexpensive and doesn’t take long at Jax Auto Repair. Lack of it, however, can put a vehicle in the scrap heap.

Talk to your Jax Auto Repair service professional for more information.

Keep Your Cool In Brea

/>Your browser does not support video

Brea auto owners rely on their car’s coolant system to keep their engine cool. Coolant (also called antifreeze) mixed with water flows through your sedan engine and absorbs heat. The mixture then flows out to the radiator where it’s cooled by air flowing over the radiator. From there the coolant/water mix circulates back through the engine to absorb more heat.

There’s a reason we mix coolant and water. Water alone actually does a good job transferring heat from the engine. The problem is that water boils at a temperature that’s easily reached inside your sedan’s engine, so it can turn to steam which does not conduct heat as well and is harder to contain.

Also, if it’s freezing outside in Brea, the water in your engine could freeze while your vehicle is sitting out in the California cold.

So, if you remember your Brea high school chemistry, you’ll know that a mixture has both a higher boiling point and a lower freezing point than either component alone.

Coolant, or antifreeze, is specially formulated to keep your engine safe in a wide range of environmental and operating temperatures in and around Brea.

Keep Your Cool In Brea Whenever your sedan is running, the coolant in the cooling system is working to keep your engine from overheating. When it’s cold outside, the coolant acts as antifreeze to keep the fluid from freezing in your engine.

All that exploding fuel in your engine creates a lot of heat. Without coolant, the metal sedan engine parts would expand so much that the engine would seize up and stop running. The costly parts could be broken or warp so badly they would have to be replaced. It could even be so bad that the whole sedan’s engine is ruined and has to be junked.

This is why it is critical that Brea drivers check coolant levels frequently and have their sedan cooling system inspected for leaks. Also your sedan car maker has a maintenance requirement for draining and replacing your coolant. These recommendations can vary widely, so check your owner’s manual or ask us at Jax Auto Repair in Brea.

The reason Brea car owners need to change the coolant is that it has additives in it to protect the cooling system. As you can imagine, with all the heat, the cooling system’s a pretty harsh environment. The additives keep the fluid from becoming corrosive and damaging the radiator and other sedan cooling system components. Over time, the additives are depleted and the coolant just has to be replaced.

Many Brea auto owners ask Jax Auto Repair why there are different colors of antifreeze. It is very important that you use the correct type of antifreeze. The different types of antifreeze – or coolant – are different colors so you don’t mix them up.

The auto makers use different materials to make the cooling system, and they require different types of antifreeze to protect them.

So check with us at Jax Auto Repair in Brea or your owner’s manual for the right kind because using the wrong coolant can void the warranty for your sedan cooling system.

Jax Auto Repair Radiator Service

The coolant system is a vital part of your vehicle. It is also the second most common cause for vehicle failures. Even though coolant system failure is fairly common, it is easy to prevent.

Jax Auto Repair
331 South Brea Boulevard
Brea, California 92821
(714) 529-2886

The most recognizable part of the coolant system is the radiator. It is connected to the engine with hoses and is filled with coolant. The coolant draws heat off the engine and then goes into the radiator. Air passes through cooling fins to reduce the temperature of the coolant and then it’s back to the engine again.

There are several ways for the cooling system to fail. Most common is with the coolant itself. Coolant is a mixture of water and antifreeze. The proper mixture keeps the coolant from either boiling away or freezing. Both of which can result in massive engine damage.

Another very important coolant issue that is often overlooked is the age of the coolant itself. Antifreeze has additives that protect the coolant system from corrosion. As these additives are depleted over time, they can’t protect the radiator and other parts from rust, scaling and corrosion. Old coolant may still keep your engine cool, but it won’t protect it from corrosion.

If you see a warning message to check the coolant or if the temperature gauge is in the hot zone your cooling system needs to be checked. It’s OK to add water or antifreeze yourself. But you need to be cautious. Remember four things.

  • First, you never want to open the radiator pressure cap. You could be severely burned.
  • Second, try to get to your Brea service center at Jax Auto Repair immediately if your coolant is low. If that is not possible, follow the directions in your owners manual – it will direct you to only make additions to the coolant overflow bottle.
  • Third, remember that you need a proper mixture of water and antifreeze. If you make an emergency addition to your cooling system, follow-up with your Jax Auto Repair service center where we can make necessary corrections.
  • Fourth, not all cars use the same type of antifreeze. You need to check your owners manual to make sure you use the right kind. Mixing antifreeze types or using the wrong kind of antifreeze may void the manufacturers warranty on your cooling system. Again, another reason to rely on your Jax Auto Repair service center in Brea to do things right.

Remember, your Brea service center has the equipment to change your coolant quickly and inexpensively.